※一部利用できない機能があります
| 1.
論文 |
論文
|
高, 炅男 ; 樅山, 智裕 ; 新井, 雅隆
概要:
application/pdf<br />Journal Article<br />Diesel spray impinged normally on a flat wall was investigated. Spray tip penetration and spray volumes of before and after impingement were measured on high speed photographs of the sprays
…
which were injected by a single shot injection system into a high pressure chamber of cold state. The effects of the spray tip penetration, spray volume, entrainment mass and air-fuel ratio were discussed on the sprays of before and after impingement. The volume of the post-impingement spray was calculated using axi-symmetrical model. It was greatly affected by the distance between the injection nozzle and the wall. When the impingement distance was shorter than the break-up length of the original spray, the entrainment mass as well as the volume of post-impingement spray was the larger than that of the original spray at the same inspection time. To calculate the average spray concentration of after impingement spray, the fuel film stuck on the wall was measured. The average air-fuel ratio of the impingement spray increased faster than the free spray because the spray concentration in a space decreased by the fuel stuck on the wall.
続きを見る
|
||
| 2.
論文 |
論文
|
江原, 拓未 ; 天谷, 賢児 ; 新井, 雅隆
概要:
application/pdf<br />Journal Article<br />In this paper, behaviors of diesel spray injected along a wall were experimentally investigated. In order to clarify the wall effect on spray structure, the geometry of the wall and its
…
relative position to the spray axis were varied. Structures of spray injected into a high-pressure atmosphere were recorded by high-speed photographs. Results shows that the asymmetrically large vortexes in the spray were induced by the wall effect, and the spray penetrating along the wall was deviated to the wall surface. This phenomenon is called the Coanda effect in the field of fluid dynamics. The growth orientation of spray was defined by image analysis. Maldistribution ratio of spray area was defined for the quantitative estimation of the spray deviation behavior. The spray deviating conditions such as the geometry of the wall and its relative position to the spray axis were fined.
続きを見る
|
||
| 3.
論文 |
論文
|
高橋, 秀夫 ; 柳沢, 洋樹 ; 志賀, 聖一 ; 柄沢, 隆夫 ; 中村, 壽雄
概要:
application/pdf<br />Journal Article<br />The atomization behavior of an intermittent fuel spray from a diesel nozzle was clearly observed by means of shadowgraphy using an image-converting camera with the framing rate of 10^5
…
f.p.s. and an image-intensified CCD camera with high-speed gating. A rather wide range of valve-opening pressure (5 to 70 MPa) was covered, and simultaneous measurement of the injection pressure inside the nozzle sac was also attempted to clarify the atomization mechanisms at its very early stage of injection. At the beginning of injection, the emergence of a liquid column was observed. Initially, it has almost the same diameter as the nozzle hole and then spreads radially, forming the spray angle in the vicinity of the nozzle exit. The timing of this spray-angle formation becomes earlier with the increase in valve opening pressure, even if the pressure inside the nozzle sac at this moment does not vary. This pressure approximately corresponds to that of the transition region in an atomization regime of a steady jet.
続きを見る
|
||
| 4.
論文 |
論文
|
高橋, 秀夫 ; 柳沢, 洋樹 ; 志賀, 聖一 ; 柄沢, 隆夫 ; 中村, 壽雄
概要:
application/pdf<br />Journal Article<br />The development of a high-pressure diesel spray in its very early stage is examined through enlarged shadowgraphs in both atmospheric and pressurized conditions. A rather wide range of valve
…
opening pressure was covered to clarify the mechanisms of the initial stage of development. At 0.3 ms after the start of injection, there is a region where the tip penetration is insensitive to the ambient pressure and it becomes shorter with the increase in valve opening pressure. This characteristic feature of the spray formation process is related to the eddy motion generated in the spray. The transition of the atomization regime from a wavy jet to a fully developed spray is also shown, and it is suggested that the pressure history in the nozzle sac is closely related to this phenomenon.
続きを見る
|
||
| 5.
論文 |
論文
|
TABATA, Michihiko ; FUJII, Hiroshi ; ARAI, Masataka ; HIROYASU, Hiroyuki
概要:
application/pdf<br />Journal Article<br />The Sauter mean diameter and size distribution of a diesel spray in a vaporizing process were studied to obtain detailed information of the diameter change of the spray in an
…
elevated-temperature and-pressure environment. In this study, direct photographs of the diffracted light from particles or spray drops were taken using a pulsed laser and analyzed directly. The mean particle size could be measured even if the diffracted light from particles passed through a high-ambient-temperature and-pressure environment. The liquids used for studying a vaporizing diesel spray were diesel fuel and n-heptane. The Sauter mean diameter increased to a maximum, then decreased with a further increase of the ambient temperature. The change of the Sauter mean diameter was different for different fuel evaporation rates. The increase of the Sauter mean diameter of n-heptane spray occurred at a lower ambient temperature condition than did that for the diesel spray.
続きを見る
|
||
| 6.
論文 |
論文
|
清水, 正則 ; 新井, 雅隆 ; 廣安, 博之
概要:
application/pdf<br />Journal Article<br />In order to elucidate the disintegrating mechanisms of a diesel spray, the breakup length was measured by an electric resistance method. A reattachment distance of separated liquid flow
…
in a nozzle and a spray were observed photographically. The mechanism of the two disintegrating processes of the jet was investigated by separating an ambient effect from a disturbed effect of the nozzle. The atomizing mechanism of the jet was governed by both the initial disturbance due to the nozzle geometry and an interfacial force between the jet and the environment. If a strong disturbance was given to the internal flow in a nozzle, the jet would be broken up into a spray flow.
続きを見る
|
||
| 7.
論文 |
論文
|
高橋, 秀夫 ; 志賀, 聖一 ; 小柴, 英俊 ; 柄沢, 隆夫 ; 倉林, 俊雄
概要:
application/pdf<br />Journal Article<br />The purpose of this study is to clarify the characteristics of diesel spray with higher and unsteady injection pressure under an elevated pressure condition and an elevated pressure and
…
temperature condition. A Bosch-type injection system and a rapid compression machine were used. The behavior of the spray until 2 ms after the beginning of injection, which corresponds to the period of the ignition delay of most diesel engines, was observed by high-speed photography. Under the less evaporating condition, the spray penetrations of higher and normal injection pressure are almost the same, whereas, under the evaporating condition, those penetrations are not the same. Thus, the penetration of the normal injection pressure is affected by the ambient temperature, while the penetration of the higher injection pressure is little affected by the evaporation. The same tendency was observed in the behavior of spray cone angle development. It is also shown that the spray generates small eddies and the spray pattern is affected by the growth and dissipation of those eddies.
続きを見る
|
||
| 8.
論文 |
論文
|
高橋, 秀夫 ; 志賀, 聖一 ; 柄沢, 隆夫 ; 倉林, 俊雄
概要:
application/pdf<br />Journal Article<br />A rapid-compression machine is developed for fundamental studies of diesel combustion. Low-pressure compressed air and a stainless-steel membrane are employed to drive the piston. This is
…
similar to the principle of a shock tube and is quite simple compared with other machines. The combustion chamber has a 120 mm bore and is 20 mm in depth. These dimensions were determined to avoid the impingement of the spray within 2ms, which seems to be a typical ignition delay period. Compression time and polytropic exponent are about 38ms and 1.30, respectively. High-speed photographs were taken to observe the spray development for both evaporating and non evaporating spray, and the effect of evaporation could be shown clearly. A combustion test was also carried out, and a pressure rise due to combustion was recognized. Thus, it is shown that this machine has sufficient performance for the study of diesel combustion. A simple simulation technique to design the machine is also presented and its availability is verified.
続きを見る
|
